Over 15 years experience of providing support of MEAN WELL Power Supplies
Image shown is a representation only. Exact specifications should be obtained from the product datasheet.
Mean Well PSD-45A-24 DC-DC Converter - 30W - 9~18V in 24V out 1.25A
Overview
PSD-45A-24 is the 24V output model of this series: rated current 1.25A, rated power 30W, typical efficiency 79%.
Features
- 2:1 wide input range
- Protections:Short circuit/Over load /Over voltage/ Polarity
- Cooling by free air convection
- Built-in EMI filter, low ripple noise
- 100% full load burn-in test
- Fixed switching frequency at 96KHZ
- Low cost
- High reliability
- 2 year warranty
Specifications
OUTPUT
- DC VOLTAGE
- 24V
- RATED CURRENT
- 1.25A
- CURRENT RANGE
- 0 ~ 1.25A
- RATED POWER
- 30W
- RIPPLE & NOISE (max.)Note.2
- 150mVp-p
- VOLTAGE ADJ RANGE
- 21.6 ~ 26.4V
- VOLTAGE TOLERANCENote.3
- ± 2.0%
- LINE REGULATION
- ± 0.5%
- LOAD REGULATION
- ± 0.5%
- SETUP, RISE, HOLD UP TIME
- 1000ms, 50ms, ----/12VDC/24VDC at full load; 1500ms,50ms,----48VDC at full load
INPUT
- VOLTAGE RANGE
- 9.2 ~18VDC (12VDC)
- EFFICIENCY(Typ.)
- 79%
- DC CURRENT(Typ.)
- 3.5A/12VDC 2.5A/24VDC 1.2A/48VDC
PROTECTION
- OVER LOAD
- 105% -160% rated output power Protection type :shut down, Re-power on after fault condition is removed
- OVER VOLTAGE
- 27.6 ~ 32.4V/10%load Protection type : Hiccup mode, recovery automatically after fault condition is removed
ENVIRONMENT
- WORKING TEMP.
- -10 ~ +60℃ (Refer to output load derating curve),20~90%RH non-condensing
- WORKING HUMIDITY
- 20 ~ 95% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -20 ~ +85℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.05%/℃ (0 ~ 50℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes
SAFETY & EMC
- SAFETY STANDARDS
- TUV BS EN/EN62368-1, EAC TP TC 004 approved
- WITHSTAND VOLTAGE
- I/P-O/P:1.5KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC
- ISOLATION RESISTANCE
- I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25℃/ 70% RH
- EMI CONDUCTION&RADIATION
- Compliance to BS EN/EN55032(CISPR32) CLASS B, EAC TP TC 020
- EMS IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,6,8,BS EN/EN55035,BS EN/EN61000-6-1 Light industry level, EAC TP TC 020
OTHERS
- MTBF
- 3067.4K hrs min. Telcordia SR-332 (Bellcore) ; 463.9K hrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 127*76*30mm (L*W*H)
- PACKING
- 0.19Kg;72pcs/15.6Kg/1.28CUFT
Test conditions and notes5
- 1.All parameters NOT specially mentioned are measured at normal input,rated load and 25℃ of ambient temperature.
- 2.Ripple & noise are measued at 20 MHz of bandwidth by using a 12inch twisted pair-wire termined with a 0.1uf & 47uf capacitor.
- 3.Tolerance:includes set up tolerance,line regulation and load regulation.
- 4.The interval of turning ON and OFF the power supply continuously is 2 seconds.
- 5.The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
Technical drawings
Downloads
FAQ
Can I use the PSD-45A-24 for a 24V PLC, HMI, or industrial control circuit on a 9-18VDC source?
Yes, this converter is built for constant-voltage 24V output from a 9.2-18VDC input. It suits 24V control equipment when the load stays within 30W and 1.25A.
Is the PSD-45A-24 a good option for 24V sensors, transmitters, or field devices in automation panels?
It can be a fit for 24V field devices that need stable constant-voltage power and have a combined demand no higher than 1.25A. Its total output capacity is 30W, so sizing should be based on both the 24V output and the 30W limit.
Can this model support a compact 24V communications or control subsystem?
Yes, if the subsystem requires 24V constant-voltage power and falls inside the converter's 30W rating. The maximum output current for this version is 1.25A, which is the main sizing limit for 24V loads.
Would the PSD-45A-24 work for a 24V embedded controller inside industrial equipment?
It is suitable for enclosed 24V embedded electronics where the available source is within 9.2-18VDC and the load does not exceed 30W. The 2:1 wide input range can also help in systems with variable input within that stated range.
Can the PSD-45A-24 be used outdoors or in exposed conditions?
The temperature spec is -10°C to +60°C, which defines its operating range. Since no IP rating is listed, the published specs do not establish suitability for outdoor, washdown, or dust-heavy environments.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other PSD-45A Models
2 other models| Model | Power | Voltage | Current | IP Rating | Price | |
|---|---|---|---|---|---|---|
| Mean Well PSD-45A-5 DC-DC Converter - 30W - 9~18V in 5V out 6A | 30W | 5V | 6A | IP20 | $20.00 | View |
| Mean Well PSD-45A-12 DC-DC Converter - 30W - 9~18V in 12V out 2.5A | 30W | 12V | 2.5A | IP20 | $20.00 | View |
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.
